Dec 29, 2025 Gadewch neges

What is another name for styrene (CAS 100-42-5)?

Styrene (CAS 100-42-5) is one of the most important monomers in the chemical industry, yet it is known by several different names depending on the source and the language of the document. Recognizing these synonyms is essential when reading safety data sheets, certificates of analysis and trade contracts. This article lists the accepted alternative names for styrene, summarizes its physical and chemical properties, provides a typical industrial specification table and explains the handling requirements that keep the monomer stable and safe.

Styrene, with the chemical formula C8H8 and a molecular weight of 104.15, is an aromatic hydrocarbon consisting of a benzene ring with a vinyl group. It is a colorless to slightly yellow liquid with a distinctive sweet, aromatic odor. Styrene is the key building block for polystyrene, styrene-acrylonitrile resins, acrylonitrile-butadiene-styrene (ABS) plastics, styrene-butadiene rubber (SBR) and unsaturated polyester resins used in coatings, composites and insulation.

Among these, vinylbenzene and phenylethylene are the most frequently encountered synonyms, and the abbreviation SM (styrene monomer) is common in the polymer and trading industries. As with all chemicals, the CAS number 100-42-5 is the definitive identifier.

Styrene is a mobile, volatile liquid with a density of about 0.909 g/cm3 at 20 ℃, a melting point of about -30.6 ℃ and a boiling point of about 145.3 ℃. Its flash point is approximately 31 ℃, which means it is flammable at ambient temperatures and must be handled away from ignition sources. Styrene is soluble in most organic solvents such as benzene, ethanol, acetone and chloroform, but only slightly soluble in water. Chemically, the vinyl group makes styrene highly reactive: it undergoes addition, oxidation, halogenation and polymerization reactions, and it hydrogenates to ethylbenzene under catalytic conditions.

100-42-5
C8H8
99.5 percent minimum
0.20 percent maximum
0.05 percent maximum
0.02 percent maximum
0.01 percent maximum
10 mg/kg maximum
10 to 15 ppm
Density at 20 ℃ About 0.909 g/cm3

These values are typical for commercial styrene monomer and are verified by the certificate of analysis supplied with each batch.

Because styrene polymerizes spontaneously, especially when heated, exposed to light or contaminated with peroxides, commercial styrene is stabilized with an inhibitor. The most common inhibitor is 4-tert-butylcatechol (TBC) at a concentration of about 10 to 15 ppm. The inhibitor is consumed over time, so storage life depends on temperature, oxygen availability and the initial inhibitor level. Product stored beyond its shelf life, or kept too warm, must be checked for polymer content before use, since excessive polymer can block equipment and degrade product quality.

Styrene is flammable, volatile and an irritant to the eyes, skin and respiratory tract, and prolonged occupational exposure is regulated in most jurisdictions. Storage tanks should be kept under inert gas blanketing with temperature control, and the product should be handled in well-ventilated areas with appropriate personal protective equipment. Transport must follow the applicable dangerous-goods regulations for flammable liquids, and containers should be inspected for leaks and proper labeling. The SDS provides the complete emergency response and exposure-control information.

Vinylbenzene and phenylethylene are the most common synonyms; styrene monomer, abbreviated SM, is also widely used in the polymer industry.

The CAS number of styrene is 100-42-5, and it is the definitive identifier regardless of the synonym used.

Styrene is only slightly soluble in water; it dissolves readily in organic solvents such as benzene, ethanol, acetone and chloroform.

TBC is a polymerization inhibitor added at 10 to 15 ppm to prevent premature polymerization during storage and transport.

No. Styrene is the liquid monomer, while polystyrene is the solid polymer produced by polymerizing styrene.

Styrene is used to produce polystyrene, ABS and SAN resins, styrene-butadiene rubber, unsaturated polyester resins and various copolymers for packaging, construction and automotive applications.

Anfon ymchwiliad

whatsapp

Dros y ffôn

E-bost

Ymchwiliad